It is currently 19 Jan 2020, 08:43




 Page 1 of 1 [ 9 posts ] 
Author Message
 Post subject: AC3 Mod on a CLD-95
PostPosted: 30 Nov 2017, 01:49 
Knows how to post
Knows how to post
User avatar

Joined: 06 Oct 2015, 22:01
Posts: 15
Location: United States
Has thanked: 0 time
Been thanked: 0 time
Anyone do one of these before? I think I've got everything figured out except the rf bit on the audio board. Benedikt's horrible instructions say:

RF = Look 1⁄4” left (towards the back) of CN505 and 1⁄4” above. Here are 2 resistors R41 and R42.
The right (towards the front) pins of both are common and are the point to tap RF. Looking at the
back side of the audio circuit board, the two resistors have jagged lightning-bolt looking symbols
representing them.

Well, there are a few spots in that general area with jagged lightning bolt symbols so it's not entirely clear where I'm supposed to be tapping in. If somebody could provide a picture with the point circled I'd greatly appreciate it.
Offline
 Profile  
 
 Post subject: Re: AC3 Mod on a CLD-95
PostPosted: 30 Nov 2017, 02:19 
Honest fan
Honest fan
User avatar

Joined: 29 Aug 2016, 21:02
Posts: 73
Location: Chicago, IL
Has thanked: 1 time
Been thanked: 2 times
The instructions are the worst. This highlights @invenio great picture instructions. He spent the time to document the process and has helped so many people. He did it on a 97 the 95's big brother. I will look at my 95 instructions tonight to see if I can help.
Offline
 Profile  
 
 Post subject: Re: AC3 Mod on a CLD-95
PostPosted: 30 Nov 2017, 02:20 
Knows how to post
Knows how to post
User avatar

Joined: 06 Oct 2015, 22:01
Posts: 15
Location: United States
Has thanked: 0 time
Been thanked: 0 time
I saw the instructions for the 97 but since they have different boards it didn't help at all.
Offline
 Profile  
 
 Post subject: Re: AC3 Mod on a CLD-95
PostPosted: 30 Nov 2017, 03:17 
Honest fan
Honest fan
User avatar

Joined: 29 Aug 2016, 21:02
Posts: 73
Location: Chicago, IL
Has thanked: 1 time
Been thanked: 2 times
This is the area below. He looks to be saying that the right side (pointing towards the front face) of both r42 and R42 are common and are the RF tap points. Do you have a picture of that area from the bottom and the top ?


Attachments:
Screen Shot 2017-11-29 at 8.04.30 PM.png
Screen Shot 2017-11-29 at 8.04.30 PM.png [ 47.48 KiB | Viewed 1138 times ]
Offline
 Profile  
 
 Post subject: Re: AC3 Mod on a CLD-95
PostPosted: 30 Nov 2017, 03:43 
Knows how to post
Knows how to post
User avatar

Joined: 06 Oct 2015, 22:01
Posts: 15
Location: United States
Has thanked: 0 time
Been thanked: 0 time
Here's a shot as if you were looking at the side of the player. To the left is the rear of the player and to the right is the front of the player.

What you've posted isn't a huge help. I can't tell what I'm looking at there.

https://scontent-ort2-1.xx.fbcdn.net/v/ ... e=5ACF2AC4
Offline
 Profile  
 
 Post subject: Re: AC3 Mod on a CLD-95
PostPosted: 30 Nov 2017, 03:51 
Jedi Master
Jedi Master
User avatar

Joined: 03 May 2004, 19:05
Posts: 6086
Location: United States
Has thanked: 167 times
Been thanked: 181 times
The picture he has posted is the same chipboard that you posted just the components side as to your solder side picture.

Not knowing anything here, it looks like you need to tap off of one of the 3 connections in that G-ground, RF-whatever that is and TBC- again whatever that is.

Should be very close to the 97, find out what was tapped on that and do the same on this board as its posted on the board you just need to know what to tap off of.

I'm no tech so do this at your own risk.
And please post this so others know how to do this in the future.
Offline
 Profile  
 
 Post subject: Re: AC3 Mod on a CLD-95
PostPosted: 30 Nov 2017, 03:53 
Knows how to post
Knows how to post
User avatar

Joined: 06 Oct 2015, 22:01
Posts: 15
Location: United States
Has thanked: 0 time
Been thanked: 0 time
But look at the original instructions. It says there would be small lightning bolt symbols where I need to tap. The area you're talking about doesn't have those symbols.
Offline
 Profile  
 
 Post subject: Re: AC3 Mod on a CLD-95
PostPosted: 30 Nov 2017, 04:19 
Honest fan
Honest fan
User avatar

Joined: 29 Aug 2016, 21:02
Posts: 73
Location: Chicago, IL
Has thanked: 1 time
Been thanked: 2 times
Ok that picture helps align both the schematic to the board. The schematic helps because each resistor is labeled so you can actually see both R42 and R41. Then when you look at your picture you can see R41 and R42 where they should be but with the lighting bolt. This is a picture of them side by side.

If you look at the other side of the board you will be able to see R41 and R42 printed next to the resistor.


Attachments:
CLD-95 mod.jpg
CLD-95 mod.jpg [ 57.64 KiB | Viewed 1133 times ]
Offline
 Profile  
 
 Post subject: Re: AC3 Mod on a CLD-95
PostPosted: 30 Nov 2017, 14:46 
Knows how to post
Knows how to post
User avatar

Joined: 06 Oct 2015, 22:01
Posts: 15
Location: United States
Has thanked: 0 time
Been thanked: 0 time
Sorry to not come back and check this. I was able to get it all figured out. I got fed up and just pulled the board and looked on the other side. Sure enough, the ones you marked there were the ones I was looking for.
Offline
 Profile  
 
Display posts from previous:  Sort by  
 Page 1 of 1 [ 9 posts ] 


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: