|
It is currently 13 May 2024, 07:21
|
View unsolved topics | View unanswered posts
|
|
|
|
Author |
Message |
jefix
|
Post subject: CLD-R7G disassembly and repair Posted: 26 Aug 2021, 07:11 |
Genuinely interested |
|
|
Joined: 11 Jul 2021, 10:51 Posts: 46 Location: Uzbekistan Has thanked: 7 times Been thanked: 3 times
|
Hello. My R7G arrived from Japan but was damaged during delivery I turned it on, I just hear a small motor inside, the tray does not open. (display lights up, I think the electronics are ok) I noticed that with a little shaking, something dangles inside the player. I removed the protective cover and found some plastic shards. https://disk.yandex.ru/i/qWXnmhueikBfmgSound is heard from this part of the player. https://disk.yandex.ru/i/Y8LYnwdin7sWTAThe case appears to be intact. I think this was due to the strong shaking. I wanted to take it apart, but the mechanism seems to be very complicated. I hope that the forum can help me with disassembling, repairing and assembling the player. Thanks.
|
|
|
|
|
cplusplus
|
Post subject: Re: CLD-R7G disassembly and repair Posted: 26 Aug 2021, 19:36 |
Hardcore fan |
|
|
Joined: 13 Aug 2018, 03:18 Posts: 1529 Has thanked: 454 times Been thanked: 592 times
|
kris wrote: My guess is a broken motorholder. Same.
|
|
|
|
|
jefix
|
Post subject: Re: CLD-R7G disassembly and repair Posted: 27 Aug 2021, 06:50 |
Genuinely interested |
|
|
Joined: 11 Jul 2021, 10:51 Posts: 46 Location: Uzbekistan Has thanked: 7 times Been thanked: 3 times
|
rein-o wrote: Don't push anything, did you pay for insurance??? Any contact from seller. I have already contacted the intermediary. An investigation is underway. Quote: My guess is a broken motorholder. If the pins break holding the gears or motorholder of the laser snapped. Is it hard to fix? I guess I can glue the broken parts together. But I'm not sure if I can assemble the device as it was. Is it a good idea to start disassembly by removing the bezel? I want to do the disassembly of the player at this time tomorrow. Can you give recommendations on what to do and what not to do?
|
|
|
|
|
jefix
|
Post subject: Re: CLD-R7G disassembly and repair Posted: 27 Aug 2021, 11:40 |
Genuinely interested |
|
|
Joined: 11 Jul 2021, 10:51 Posts: 46 Location: Uzbekistan Has thanked: 7 times Been thanked: 3 times
|
knatterbuechse wrote: Try to find a copy of the Pioneer CLD-210KVT service manual. From what I remember it's pretty close to the R7G. It should give you the information you need to pull out / remove the tray and figure out where the broken piece might be located on the inside (plus its part number). Might be worth a shot. As I understood from the instructions, I need to turn on the player and open the tray. It seems impossible in my case. https://yadi.sk/i/y9ZKujW_M3-DsA
|
|
|
|
|
jefix
|
Post subject: Re: CLD-R7G disassembly and repair Posted: 30 Aug 2021, 09:32 |
Genuinely interested |
|
|
Joined: 11 Jul 2021, 10:51 Posts: 46 Location: Uzbekistan Has thanked: 7 times Been thanked: 3 times
|
cplusplus wrote: You need to eject the tray manually by turning the pulley with the belt around it. Can you show in the picture what I have to move, please? I tried to turn the gears, but it seems it was for the laser: https://yadi.sk/i/N9iH3HZ-e7XgGwBy the way, I tried to turn on the player without laser and open the tray. I got error E0. I plugged in the laser and did the same and got the same error. At the same time, the motor on the laser was spinning. It looks like some kind of sensor should work for the tray to start opening. Quote: The bar is the rod that the laser runs on, the other is the actual laser I think with motor for the laser to move it back and forth. I got what you mean. I'm surprised that there is no lubricant on the rod. Or it has dried up.
|
|
|
|
|
cplusplus
|
Post subject: Re: CLD-R7G disassembly and repair Posted: 30 Aug 2021, 17:51 |
Hardcore fan |
|
|
Joined: 13 Aug 2018, 03:18 Posts: 1529 Has thanked: 454 times Been thanked: 592 times
|
jefix wrote: cplusplus wrote: You need to eject the tray manually by turning the pulley with the belt around it. Can you show in the picture what I have to move, please? I tried to turn the gears, but it seems it was for the laser: https://yadi.sk/i/N9iH3HZ-e7XgGwThe pulley with rubber belt around it that you labeled "I twisted it". One way raises the mech, the other ejects the tray.
|
|
|
|
|
cplusplus
|
Post subject: Re: CLD-R7G disassembly and repair Posted: 01 Sep 2021, 00:11 |
Hardcore fan |
|
|
Joined: 13 Aug 2018, 03:18 Posts: 1529 Has thanked: 454 times Been thanked: 592 times
|
jefix wrote: I don’t see where the plastic shards came off yet. Probably here: Attachment:
Clip.jpg [ 127.89 KiB | Viewed 3314 times ]
|
|
|
|
|
|
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
|