|
It is currently 23 Apr 2024, 07:36
|
View unsolved topics | View unanswered posts
|
|
|
|
cplusplus
|
Post subject: Re: Sencore Lumagen Radiance XE power supply replacement Posted: 12 May 2020, 00:15 |
Hardcore fan |
|
|
Joined: 13 Aug 2018, 03:18 Posts: 1519 Has thanked: 448 times Been thanked: 587 times
|
rein-o wrote: I would try to contact the company and find out from them directly. I believe Substance has said they will respond about issues and should be able to let you know the best. Good luck. Yeah they seem pretty helpful. Try sending an email to support@lumagen.com
|
|
|
|
|
katleta5000
|
Post subject: Re: Sencore Lumagen Radiance XE power supply replacement Posted: 17 May 2020, 09:37 |
Third post and above |
|
|
Joined: 04 Mar 2020, 20:43 Posts: 6 Location: Ukraine Has thanked: 2 times Been thanked: 0 time
|
deadlegion wrote: Personally I would try: Buying the 4 Pin plug, figure out the wiring/polarity and then wire up 12v power from desktop PC PSU (easy to find for $0). It should work. substance wrote: This is the reply I got from Jim at Lumagen.
“ Looking at the back of the XE unit the jack has Ground on the lower left and +12 on the upper left. Someone with basic soldering skills could transfer the plug to another 12 VDC at 2.5 Amp (or more current) power brick. ” It will help me. Thank you all for help!
|
|
|
|
|
katleta5000
|
Post subject: Re: Sencore Lumagen Radiance XE power supply replacement Posted: 14 Jun 2020, 14:08 |
Third post and above |
|
|
Joined: 04 Mar 2020, 20:43 Posts: 6 Location: Ukraine Has thanked: 2 times Been thanked: 0 time
|
substance wrote: This is the reply I got from Jim at Lumagen.
“ Looking at the back of the XE unit the jack has Ground on the lower left and +12 on the upper left. Someone with basic soldering skills could transfer the plug to another 12 VDC at 2.5 Amp (or more current) power brick. ” That is absolutely accurate, thank you! If some one needs you can check it by disassemble the unit and on the main board there is "test" spot with 12 volts/ground titles. With a multimeter you can ping this spots with input connector and figure out what pin is +12 and ground. Connector outer shielding also grounded.
Attachments: |
File comment: Lumagen 4pin connector
connector.jpg [ 112.72 KiB | Viewed 3160 times ]
|
File comment: Lumagen board
board.jpg [ 313.17 KiB | Viewed 3160 times ]
|
|
|
|
|
|
katleta5000
|
Post subject: Re: Sencore Lumagen Radiance XE power supply replacement Posted: 14 Jun 2020, 14:17 |
Third post and above |
|
|
Joined: 04 Mar 2020, 20:43 Posts: 6 Location: Ukraine Has thanked: 2 times Been thanked: 0 time
|
My PSU replacement arrived finally. And it works fine. There are models LiteOn PA-1081-01 and NL-A69J from Sharp. It cost me 10$ each, LiteOn was new. Bought both just in case Because the device itself quite old, it was very hard to find what PSU model needed, maybe all this information will help some one. Thanks to everyone for advice!
Attachments: |
1112.jpg [ 157.88 KiB | Viewed 3160 times ]
|
111.jpg [ 209.84 KiB | Viewed 3160 times ]
|
|
|
|
|
|
|
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
|