It is currently 28 Mar 2024, 10:34




 Page 1 of 1 [ 11 posts ] 
Author Message
 Post subject: [CLD-2070][CLD-3070][CLD-91][CLD-92] Loading Disassembly
PostPosted: 03 Jun 2022, 03:20 
Hardcore fan
Hardcore fan
User avatar

Joined: 13 Aug 2018, 03:18
Posts: 1512
Has thanked: 443 times
Been thanked: 584 times
Here is how I disassemble the loading assembly for cleaning and re-greasing on this chassis.

Remove the four screws holding the front panel and the four screws holding the board assemblies:
Attachment:
Top_Screws.jpg
Top_Screws.jpg [ 154.86 KiB | Viewed 1726 times ]


Remove three screws on the rear:
Attachment:
Back_Screws.jpg
Back_Screws.jpg [ 52.93 KiB | Viewed 1726 times ]


Pull the front panel down:
Attachment:
Front_Panel.jpg
Front_Panel.jpg [ 110.78 KiB | Viewed 1726 times ]


The panel can be moved to the side without disconnecting anything:
Attachment:
Front_Panel_Side.jpg
Front_Panel_Side.jpg [ 105.7 KiB | Viewed 1726 times ]


Lift each board assembly up. The white holders can be turned to hold them open:
Attachment:
Board_Holders.jpg
Board_Holders.jpg [ 149.61 KiB | Viewed 1726 times ]
Offline
 Profile  
 
 Post subject: Re: [CLD-2070][CLD-3070][CLD-91][CLD-92] Loading Disassembly
PostPosted: 03 Jun 2022, 03:38 
Hardcore fan
Hardcore fan
User avatar

Joined: 13 Aug 2018, 03:18
Posts: 1512
Has thanked: 443 times
Been thanked: 584 times
Carefully remove the clamper springs. They are easily damaged.
Attachment:
Clamper_Spring.jpg
Clamper_Spring.jpg [ 98.56 KiB | Viewed 1725 times ]


Gently push the catch in the back right slighter towards the power supply and pull the slider towards the front so the clamper can be pulled up and out.
Attachment:
Slider_Rest.jpg
Slider_Rest.jpg [ 225.73 KiB | Viewed 1725 times ]


Below is the position where the clamper can be pulled up:
Attachment:
Slider_Clamper.jpg
Slider_Clamper.jpg [ 125.3 KiB | Viewed 1725 times ]


Unscrew the grounding screw and remove wiring from harnesses:
Attachment:
Loading_Wiring.jpg
Loading_Wiring.jpg [ 90.26 KiB | Viewed 1725 times ]


Remove the two zip ties, unbend the holder and unplug the two connectors that lead to the loading assembly.
Attachment:
Wiring_Ties.jpg
Wiring_Ties.jpg [ 95.22 KiB | Viewed 1725 times ]
Offline
 Profile  
 
 Post subject: Re: [CLD-2070][CLD-3070][CLD-91][CLD-92] Loading Disassembly
PostPosted: 03 Jun 2022, 03:54 
Hardcore fan
Hardcore fan
User avatar

Joined: 13 Aug 2018, 03:18
Posts: 1512
Has thanked: 443 times
Been thanked: 584 times
Push the right slider all the way forward and lift the loading assembly out of the player. Turn it over and you will see three gears with locking rings around them. Very carefully remove these locking rings and set them somewhere safe. I will not be disassembling the large cam gear on the right in this guide, but it is sometimes required.
Attachment:
Loading_Gears.jpg
Loading_Gears.jpg [ 109.92 KiB | Viewed 1725 times ]


Pull the gears up (don't worry about any timing). Clean the posts and inside of the gears. Regrease everything you are able to clean that has old grease on it with new grease. I use EM-30L.
Attachment:
Gear_Posts.jpg
Gear_Posts.jpg [ 37.14 KiB | Viewed 1725 times ]


Here is the goop that can hide under these gears that must be removed:
Attachment:
Old_Grease.jpg
Old_Grease.jpg [ 27.69 KiB | Viewed 1725 times ]


If you see any white grease on the loading motor gear (under the black plastic sheet), remove it all and do not replace it. If you have a new belt, replace it. If not, ensure the old one does not have any grease on it.
Attachment:
Bad_Grease.jpg
Bad_Grease.jpg [ 102.83 KiB | Viewed 1725 times ]


While everything is out of the player, clean off any other bad grease around the left and right sliders and replace it. I take this time to easily clean the spindle grip with a cotton swab and water and clean the part of the spindle that meets the clamper and apply a dot of grease to it.
Attachment:
Chassis.jpg
Chassis.jpg [ 221.4 KiB | Viewed 1725 times ]
Offline
 Profile  
 
 Post subject: Re: [CLD-2070][CLD-3070][CLD-91][CLD-92] Loading Disassembly
PostPosted: 03 Jun 2022, 04:04 
Hardcore fan
Hardcore fan
User avatar

Joined: 13 Aug 2018, 03:18
Posts: 1512
Has thanked: 443 times
Been thanked: 584 times
Insert the loading assembly back in the player. Ensure this plastic piece goes back onto this screw:
Attachment:
Carrier.jpg
Carrier.jpg [ 35.47 KiB | Viewed 1722 times ]


Next, move the right slider one position back, but not all the way where the catch will engage. Insert the clamper, and move the slider back so the catch engages. Reattach the springs.

Remove the gear that is on the top of the loading assembly (again being careful with the locking ring), clean and regrease and put it back. Your timing should look like below:
Attachment:
Loading_Timing.jpg
Loading_Timing.jpg [ 155.92 KiB | Viewed 1722 times ]


Manually load and unload the player fully in each direction and ensure it all has been reassembled correctly before reattaching wiring to harnesses, etc.

[To Be Continued]
Offline
 Profile  
 
 Post subject: Re: [CLD-2070][CLD-3070][CLD-91][CLD-92] Loading Disassembly
PostPosted: 05 Jun 2022, 20:40 
Hardcore fan
Hardcore fan
User avatar

Joined: 28 Jun 2014, 05:59
Posts: 1451
Location: San Francisco, CA USA
Has thanked: 415 times
Been thanked: 527 times
Thanks for this tutorial cplusplus.

Been awhile since I worked on someone else's 3070 and I was already forgetting how I worked on it. This will be very useful when I get around to tackling the 3070 I acquired a few months back :thumbup:.
Offline
 Profile  
 
 Post subject: Re: [CLD-2070][CLD-3070][CLD-91][CLD-92] Loading Disassembly
PostPosted: 19 Jul 2022, 22:52 
Third post and above
Third post and above
User avatar

Joined: 24 Nov 2021, 08:30
Posts: 4
Location: United States
Has thanked: 0 time
Been thanked: 0 time
This has been so helpful. I recently cleaned and put new grease on my CLD-91. I managed to lose the roller that goes between the gear and the rack. It looks like I could use something else in its place, but I'm not sure exactly what. The part also doesn't seem to exist any longer (VNL1147). I'm curious if you have suggestions. I'm assuming the drawer won't work properly without it.

The player works. I haven't been able to get the drawer/loading timing completely right, even with photos. The mechanism started to work until I put the upper gear and gear holder assembly back on. That got me back to where I started. The drawer doesn't want to open.
Offline
 Profile  
 
 Post subject: Re: [CLD-2070][CLD-3070][CLD-91][CLD-92] Loading Disassembly
PostPosted: 20 Jul 2022, 02:19 
Hardcore fan
Hardcore fan
User avatar

Joined: 13 Aug 2018, 03:18
Posts: 1512
Has thanked: 443 times
Been thanked: 584 times
I'll see if I can fish one out and measure it.
Offline
 Profile  
 
 Post subject: Re: [CLD-2070][CLD-3070][CLD-91][CLD-92] Loading Disassembly
PostPosted: 21 Jul 2022, 05:25 
Third post and above
Third post and above
User avatar

Joined: 24 Nov 2021, 08:30
Posts: 4
Location: United States
Has thanked: 0 time
Been thanked: 0 time
Thanks. I found it. It's so small it blended in. I'd set it on a metal piece in the player.

I've gotten the player to work, but there's kind of a snap when it opens and closes, so I think my timing is a little off. But it wouldn't open at all before, so this is huge.
Offline
 Profile  
 
 Post subject: Re: [CLD-2070][CLD-3070][CLD-91][CLD-92] Loading Disassembly
PostPosted: 21 Jul 2022, 19:40 
Hardcore fan
Hardcore fan
User avatar

Joined: 28 Jun 2014, 05:59
Posts: 1451
Location: San Francisco, CA USA
Has thanked: 415 times
Been thanked: 527 times
Maybe this video can help (or maybe not).

This is a 3070 I worked on awhile back after I got the old grease removed.

Offline
 Profile  
 
 Post subject: Re: [CLD-2070][CLD-3070][CLD-91][CLD-92] Loading Disassembly
PostPosted: 10 Oct 2022, 05:28 
Honest fan
Honest fan
User avatar

Joined: 23 Jan 2018, 05:28
Posts: 66
Location: United States
Has thanked: 10 times
Been thanked: 25 times
Great write-up, cplusplus!

I have a CLD-91 coming in tomorrow that has the glued up gear issue.

A couple questions, at which step do you remove the tray? Are you able manually eject the tray, or does it come out as part of taking all of this apart?

This doesn't seem like an easy task, but with patience and paying attention to your steps, it will make things easier. I may reach out if I can't decipher something from the photos, mainly taking the slider assembly apart.
Offline
 Profile  
 
 Post subject: Re: [CLD-2070][CLD-3070][CLD-91][CLD-92] Loading Disassembly
PostPosted: 03 Nov 2023, 03:00 
Second post
Second post
User avatar

Joined: 01 Nov 2023, 08:43
Posts: 2
Location: United States
Has thanked: 0 time
Been thanked: 0 time
cplusplus wrote:
Push the right slider all the way forward and lift the loading assembly out of the player. Turn it over and you will see three gears with locking rings around them. Very carefully remove these locking rings and set them somewhere safe. I will not be disassembling the large cam gear on the right in this guide, but it is sometimes required.
Attachment:
Loading_Gears.jpg


Pull the gears up (don't worry about any timing). Clean the posts and inside of the gears. Regrease everything you are able to clean that has old grease on it with new grease. I use EM-30L.
Attachment:
Gear_Posts.jpg


Here is the goop that can hide under these gears that must be removed:
Attachment:
Old_Grease.jpg


If you see any white grease on the loading motor gear (under the black plastic sheet), remove it all and do not replace it. If you have a new belt, replace it. If not, ensure the old one does not have any grease on it.
Attachment:
Bad_Grease.jpg


While everything is out of the player, clean off any other bad grease around the left and right sliders and replace it. I take this time to easily clean the spindle grip with a cotton swab and water and clean the part of the spindle that meets the clamper and apply a dot of grease to it.
Attachment:
Chassis.jpg



I took the cam apart, I need help :(
Offline
 Profile  
 
Display posts from previous:  Sort by  
 Page 1 of 1 [ 11 posts ] 


Who is online

Users browsing this forum: No registered users and 11 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: