|
It is currently 26 Apr 2024, 15:05
|
View unsolved topics | View unanswered posts
|
|
|
|
martymcflyjr33
|
Post subject: Re: [CLD-A100] Looping playback Issue Posted: 29 Jun 2021, 01:40 |
Third post and above |
|
|
Joined: 28 Jun 2021, 18:56 Posts: 7 Location: United States Has thanked: 2 times Been thanked: 0 time
|
rein-o wrote: I'm not a tech but it sounds like centering but if CDs play then it shouldn't be that. Also sounds like its something from keeping it to get to the end of the disc. Did you remove parts and not get the gears aligned when putting back together????
Can't remember the terminology now for what is going on, I sort of remember reading stuff like this on players with bad M-holders but this isn't supposed to be one of those players.
Hope others chime in to help who have knowledge. Also can't believe there were 200 caps, I do believe it but its crazy that you needed to replace all but good job on that part. Thanks for the response! Yeah, it was a big undertaking to replace over 200 caps, but I really want this to last a long time! I really love using it even though I only have one movie (Bladerunner, but planning to get more). Yes, it is strange. It plays absolutely perfectly all the way up until the last few minutes. Even stranger, I can't access the "Supplementary Section" at the end of Side 4 of Bladerunner. I really hope I can get this solved. Cheers!
|
|
|
|
|
ldfan
|
Post subject: Re: [CLD-A100] Looping playback Issue Posted: 29 Jun 2021, 19:24 |
Hardcore fan |
|
|
Joined: 28 Jun 2014, 05:59 Posts: 1459 Location: San Francisco, CA USA Has thanked: 425 times Been thanked: 533 times
|
The A100 sled mechanism should be similar to other single side players with a belt driven sled assembly. Check the following..... Sled belt marked in "blue" for excessive play. If it feels normal, remove and clean the belt and the gears it touches w/ alcohol as it could be slipping due to dirt or grease. If too loose, need to order a new carriage assembly drive belt (part VEB-1077). You can find one here.... https://console5.com/store/catalogsearc ... q=cld-a100Sled gearing marked in "yellow" might show cracks on the track. I have cracks on mine but they don't affect playback. However, if a crack is big enough, it can impede movement. If you have cracks, see if they coincide w/ the timing of your skipping issue. Not sure what the solution would be if it's really bad. Metal sled marked in "red" could need cleaning and then a new coat of a light synthetic oil that is safe for plastic. I use one geared for slot car motors. Hope this is helpful.
|
|
|
|
|
martymcflyjr33
|
Post subject: Re: [CLD-A100] Looping playback Issue Posted: 30 Jun 2021, 13:03 |
Third post and above |
|
|
Joined: 28 Jun 2021, 18:56 Posts: 7 Location: United States Has thanked: 2 times Been thanked: 0 time
|
ldfan wrote: The A100 sled mechanism should be similar to other single side players with a belt driven sled assembly. Check the following..... Sled belt marked in "blue" for excessive play. If it feels normal, remove and clean the belt and the gears it touches w/ alcohol as it could be slipping due to dirt or grease. If too loose, need to order a new carriage assembly drive belt (part VEB-1077). You can find one here.... https://console5.com/store/catalogsearc ... q=cld-a100Sled gearing marked in "yellow" might show cracks on the track. I have cracks on mine but they don't affect playback. However, if a crack is big enough, it can impede movement. If you have cracks, see if they coincide w/ the timing of your skipping issue. Not sure what the solution would be if it's really bad. Metal sled marked in "red" could need cleaning and then a new coat of a light synthetic oil that is safe for plastic. I use one geared for slot car motors. Hope this is helpful. Wow! Thank you so much for the response! I replaced both belts on the LaserActive, so I should be good in that department. I checked for cracks and couldn't find any. I also thoroughly cleaned and re-greased all rails and gears. I am actually now having another issue. The laser doesn't want to focus anymore and thus does not recognize CDs or LDs. The laser itself is working but it wont move up and down vertically to adjust focus. Do you know what may be causing this?
|
|
|
|
|
|
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
|