It is currently 20 Oct 2019, 10:34




 Page 1 of 1 [ 7 posts ] 
Author Message
 Post subject: HLD-X9 error
PostPosted: 05 Jan 2017, 08:29 
Hardcore fan
Hardcore fan
User avatar

Joined: 05 Dec 2006, 19:08
Posts: 1092
Location: Belgium
Has thanked: 11 times
Been thanked: 1 time
Anyone have any info on the P5 error displayed on the HLD-X9.
Any repair suggestions?
_________________
CLD-D925
LD-V4400
Lexicon LDD-1
Lumagen Radiance XD
SR-7007
RMB-1585
DMP-UB900
TX-58DX780E
Offline
 Profile  
 
 Post subject: Re: HLD-X9 error
PostPosted: 05 Jan 2017, 19:39 
Honest fan
Honest fan
User avatar

Joined: 29 Oct 2013, 15:56
Posts: 116
Location: United Kingdom
Has thanked: 2 times
Been thanked: 1 time
Is the error on all discs or just Muse discs? I had an X9 popping a P5 error on Muse discs only and it turned out to be the Syps board was at fault.
Offline
 Profile  
 
 Post subject: Re: HLD-X9 error
PostPosted: 05 Jan 2017, 23:50 
Hardcore fan
Hardcore fan
User avatar

Joined: 05 Dec 2006, 19:08
Posts: 1092
Location: Belgium
Has thanked: 11 times
Been thanked: 1 time
Both type of discs show this error.... what could be the problem...? What board? :crazy:
_________________
CLD-D925
LD-V4400
Lexicon LDD-1
Lumagen Radiance XD
SR-7007
RMB-1585
DMP-UB900
TX-58DX780E
Offline
 Profile  
 
 Post subject: Re: HLD-X9 error
PostPosted: 06 Jan 2017, 01:04 
Honest fan
Honest fan
User avatar

Joined: 29 Oct 2013, 15:56
Posts: 116
Location: United Kingdom
Has thanked: 2 times
Been thanked: 1 time
Mine was specific to Muse discs and it turned out the system power supply board was at fault. Your best bet is to ask Kurtis who can hopefully point you in the right direction. I think P5 is a spindle error? Kurtis will know more
Offline
 Profile  
 
 Post subject: Re: HLD-X9 error
PostPosted: 06 Jan 2017, 03:52 
Hardcore fan
Hardcore fan
User avatar

Joined: 10 May 2007, 03:12
Posts: 1173
Location: United States
Has thanked: 0 time
Been thanked: 48 times
Either spindle motor is not spinning up fast enough, this would either be the power supply or spindle motor, or the laser is bad either the laser itself or the logic on the top right board not properly driving the laser.
Offline
 Profile  
 
 Post subject: Re: HLD-X9 error
PostPosted: 06 Jan 2017, 13:21 
True fan
True fan
User avatar

Joined: 19 May 2006, 20:41
Posts: 466
Location: Belgium
Has thanked: 1 time
Been thanked: 4 times
Maybe the test mode could bring more clarity, have a look at the service manual, P5 is indeed spindle speed can not be reached in 60 seconds, action is to open top to see what happens according manual...
Offline
 Profile  
 
 Post subject: Re: HLD-X9 error
PostPosted: 06 Jan 2017, 14:18 
True fan
True fan
User avatar

Joined: 19 May 2006, 20:41
Posts: 466
Location: Belgium
Has thanked: 1 time
Been thanked: 4 times
Kris, two other points :
Is your power converter strong enough? I know spindle motor consumes a lot, if your down converter is weak it can not deliver, have experienced this myself with a US player.

Did you try a 20 cm disc, the spindle motor requires less power than for a 30 cm disc.
Offline
 Profile  
 
Display posts from previous:  Sort by  
 Page 1 of 1 [ 7 posts ] 


Who is online

Users browsing this forum: No registered users and 0 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

cron