It is currently 09 Aug 2020, 12:04




 Page 24 of 24 [ 468 posts ]  Go to page Previous  1 ... 20, 21, 22, 23, 24
Author Message
 Post subject: Re: (WIP) Laserdisc software image decoder from raw signal
PostPosted: 28 Jul 2020, 00:30 
Shows curiousity
Shows curiousity
User avatar

Joined: 14 Jul 2019, 02:53
Posts: 19
Location: United States
Has thanked: 3 times
Been thanked: 1 time
happycube wrote:
The V2600 is really a CLD-S201 with a serial port. If you get a good deal on it and it's fixable, it's still nice :)


Yeah! It came from a high school library across the state so I'm assuming the laser has low hours. Unless it was on an A/V cart and used in classrooms. When I was in high school we had a LaserDisc player (possibly this exact model) and I was intrigued by the perfect freeze frame capabilities.

Looking at the design of the consumer model I immediately see two easily accessible belts. Hopefully the disc transport is the same and I can get to those without much trouble. The seller claims it doesn't eject and makes a noise, which is either going to be a bad belt or lubrication issue.

Image


Last edited by titan91 on 30 Jul 2020, 02:32, edited 1 time in total.
Offline
 Profile  
 
 Post subject: Re: (WIP) Laserdisc software image decoder from raw signal
PostPosted: 30 Jul 2020, 02:29 
Shows curiousity
Shows curiousity
User avatar

Joined: 14 Jul 2019, 02:53
Posts: 19
Location: United States
Has thanked: 3 times
Been thanked: 1 time
My player came in today. Unfortunately the power supply board was either missing the rear screw or it fell out in shipping. This resulted in the board breaking on both ends. The front end is just a mounting point but the back end severed a jumper and a few traces in the mains AC section. Does anyone know of a spare board I can buy? If not I'll epoxy it back together and run some jumper wires.

Image
Image
Image

It also arrived with the laser sled unsecured which I think broke the plastic shield covering the focus mechanism. Luckily, the mechanism seems undamaged. I think this was done because the tray would not close. This appears to be due to the toothed bar of the sled getting stuck under the large black gear in the front as the sled rises up. This in turn seems to not line up with a small gap in the teeth, meaning the previous owner probably jumped the teeth pushing the tray in.

Image
Image

I also found this part loose in the machine. If doesn't appear to be broken. Can someone tell me where it goes?

Image
Offline
 Profile  
 
 Post subject: Re: (WIP) Laserdisc software image decoder from raw signal
PostPosted: 30 Jul 2020, 17:15 
True fan
True fan
User avatar

Joined: 27 Jul 2014, 20:59
Posts: 281
Location: North London
Has thanked: 71 times
Been thanked: 84 times
Had this happen to my dreamcast psu. If you're handy with a soldering iron then it shouldnt be too difficult to repair. I would suggest scraping back the trace to copper and solder a thick piece of copper across the break. I usually strip a coax and use the copper. Epoxy the board before you solder for added strength.
Offline
 Profile  
 
 Post subject: Re: (WIP) Laserdisc software image decoder from raw signal
PostPosted: 30 Jul 2020, 17:36 
Shows curiousity
Shows curiousity
User avatar

Joined: 14 Jul 2019, 02:53
Posts: 19
Location: United States
Has thanked: 3 times
Been thanked: 1 time
That sounds like a plan. If it get it working and some CXADC captures (can't afford a Domesday Duplicator) I'll come back to this thread with some links.
Offline
 Profile  
 
 Post subject: Re: (WIP) Laserdisc software image decoder from raw signal
PostPosted: 31 Jul 2020, 00:42 
Shows curiousity
Shows curiousity
User avatar

Joined: 14 Jul 2019, 02:53
Posts: 19
Location: United States
Has thanked: 3 times
Been thanked: 1 time
My machine appears to be a loss (to me anyway). The power supply board has components on the other side damaged as well as the transformer. It's also not removable because Pioneer in their infinite wisdom used soldered in cables. If anyone wants it for cheap parts PM me.

Back on topic.
Offline
 Profile  
 
 Post subject: Re: (WIP) Laserdisc software image decoder from raw signal
PostPosted: 05 Aug 2020, 11:47 
Knows how to post
Knows how to post
User avatar

Joined: 13 Oct 2018, 12:06
Posts: 11
Location: Germany
Has thanked: 0 time
Been thanked: 0 time
I have a few DD boards left, in case someone is interested: Domesday Duplicator boards available

Thanks go to the creators of the hard- and software. Awesome project!
Offline
 Profile  
 
 Post subject: Re: (WIP) Laserdisc software image decoder from raw signal
PostPosted: 07 Aug 2020, 05:02 
Honest fan
Honest fan
User avatar

Joined: 12 Sep 2015, 05:57
Posts: 89
Location: United States
Has thanked: 1 time
Been thanked: 5 times
Getting there (with LimeSDR as capturing device)...

Image

The LD player i am using is a spare Frankenstein player that i put together from 2 broken ones. It has RF noise and crosstalk issues, so part of the "badness" of the picture is from that. I'm going to work on making an example video from some of my samples and will report back.

(capture is from this disc/set: https://www.lddb.com/laserdisc/18974/EE ... al-Edition)
Offline
 Profile  
 
 Post subject: Re: (WIP) Laserdisc software image decoder from raw signal
PostPosted: 07 Aug 2020, 07:59 
Honest fan
Honest fan
User avatar

Joined: 12 Sep 2015, 05:57
Posts: 89
Location: United States
Has thanked: 1 time
Been thanked: 5 times
LimeSDR LD-Decode video:

https://www.youtube.com/watch?v=9MSYT7V-wcA

There are a lot of parameters to tune on the LimeSDR, so this is just basically some trial and error type stuff.
Offline
 Profile  
 
Display posts from previous:  Sort by  
 Page 24 of 24 [ 468 posts ]  Go to page Previous  1 ... 20, 21, 22, 23, 24


Who is online

Users browsing this forum: No registered users and 0 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: