It is currently 28 Mar 2024, 11:06




 Page 2 of 3 [ 45 posts ]  Go to page Previous  1, 2, 3  Next
Author Message
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 20 Aug 2019, 19:12 
Hardcore fan
Hardcore fan
User avatar

Joined: 28 Jun 2014, 05:59
Posts: 1451
Location: San Francisco, CA USA
Has thanked: 415 times
Been thanked: 527 times
It looks like most of gears (even slightly worn) should not be a problem. The missing tooth on the tray could be an issue but maybe not since it’s just needed for loading / unloading.

The issue, at least to me, is that you just need to extract the tray completely so you can re-align it with the rest of the system. I re-installed a tray incorrectly before on my CLD-59 after a belt change and it was getting half way stuck as well. It was difficult to remove and I admit I had to force it out at some point but thank goodness nothing broke. I found that I had re-inserted the tray in a slight angle that caused the misalignment but once I got it right it was fine again.
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 21 Aug 2019, 08:06 
Serious fan
Serious fan
User avatar

Joined: 19 Aug 2019, 07:23
Posts: 175
Location: Australia
Has thanked: 121 times
Been thanked: 42 times
Spent ages on the unit today ... not sure if Im progressing...learnt a lot more though...still more questions than results atm!

I understand at least some of the mechanism now much better..however as Ive experienced these units are complex enough to trip me up over and over.

Today I disassembled the loading tray mechanism and removed it and the servo mechanism from the chassis.

Carefully disassembled the loading mech plastic gears etc....obviously the black plastic cam is a crucial piece and has to be put back in the correct position taking into account switch levers and their pins that run in the cams tracks...as well as the top sliding plastic piece which also has a pin that sits in a cam groove.

Eventually managed to get the tray to slide in and out unhindered.....and then reassembled the whole unit to test.

When I turned on the unit made a noise whining noise . When i press open the display says 'open' but the tray did not move..the tray motor did not try to move at all....again though a noise can be heard...looking around I could see the laser pickup gears try to move the laser assembly along its track... but seemingly couldnt.

Thats where Im at... looking like another disassembly to try and figure out why ...not sure why the laser pickup on the rail is not moving.

Can anyone confirm that the laser assembly has to be in the right position before the tray motor would start ? this is what Im hoping is wrong stopping the tray motor to start...otherwise I have more of a problem than just the movement of the laser!

Also can anyone confirm that the laser should be able to be moved along the track manually by rotating its gears? At the moment its stuck and will not budge manually either. (I Should have checked this before reassembly !!)

Its hard to know if the operation of the tray is correct when you dont know what a working 703/770//704 tray operation lookslike (when you push it in and out manually)...I can describe whats happening here...you can pull the tray in and out now fully...and the laser tray does not raise or lower....is this correct ?

Thanks for any info and help !
_________________
CLD-D770 OK
CLD-2850 FLD,R201
CLD-D780 MHolder, PSU C12
CLD-2290 Digital Prob
CLD-2590K Lots issues
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 21 Aug 2019, 08:47 
Serious fan
Serious fan
User avatar

Joined: 19 Aug 2019, 07:23
Posts: 175
Location: Australia
Has thanked: 121 times
Been thanked: 42 times
UPDATE NEWSFLASH :)

Tray mech now working nicely!

Laser now moving along track easily!

Player now playing "Stargate" Laserdisc :)

However...... When the disc spins up...it sounds like its slipping or struggling? First time I put the disc in it spun up then stopped without playing....now its playing.

Tried selecting B side of disc...noise at rear did not work ?? another jam somewhere perhaps !
_________________
CLD-D770 OK
CLD-2850 FLD,R201
CLD-D780 MHolder, PSU C12
CLD-2290 Digital Prob
CLD-2590K Lots issues
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 21 Aug 2019, 08:48 
Serious fan
Serious fan
User avatar

Joined: 19 Aug 2019, 07:23
Posts: 175
Location: Australia
Has thanked: 121 times
Been thanked: 42 times
By the way shout out to Admin for fixing my access today.! Thankyou !


Last edited by d770 on 21 Aug 2019, 10:08, edited 1 time in total. _________________
CLD-D770 OK
CLD-2850 FLD,R201
CLD-D780 MHolder, PSU C12
CLD-2290 Digital Prob
CLD-2590K Lots issues
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 21 Aug 2019, 10:06 
Serious fan
Serious fan
User avatar

Joined: 19 Aug 2019, 07:23
Posts: 175
Location: Australia
Has thanked: 121 times
Been thanked: 42 times
Here is the 770 working today! :D
still to fix the rotating laser to be able to play both sides automatically. So atm we have a one sided player!
Will have another go tomorrow or friday...

_________________
CLD-D770 OK
CLD-2850 FLD,R201
CLD-D780 MHolder, PSU C12
CLD-2290 Digital Prob
CLD-2590K Lots issues
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 21 Aug 2019, 11:30 
Serious fan
Serious fan
User avatar

Joined: 19 Aug 2019, 07:23
Posts: 175
Location: Australia
Has thanked: 121 times
Been thanked: 42 times
So I think the grip ring on the spindle is worn hence the slipping sound on spin up....so going to need to fix that.

Ive read here that 'plastidip' can be used to help with this issue....do you spray / brush the plastidip onto the existing rubber grip ring ? or do you remove the existing grip ring clean and spray or brush the plastidip on?
_________________
CLD-D770 OK
CLD-2850 FLD,R201
CLD-D780 MHolder, PSU C12
CLD-2290 Digital Prob
CLD-2590K Lots issues
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 21 Aug 2019, 14:49 
Hardcore fan
Hardcore fan
User avatar

Joined: 28 Jun 2014, 05:59
Posts: 1451
Location: San Francisco, CA USA
Has thanked: 415 times
Been thanked: 527 times
Congrats on getting it working. And yes, you do have either a dirty or worn grip ring. You can try to clean it first with alcohol but that may only fix it temporarily (I use Intraclean to essentially revitalize the rubber and it works great but the chemical is no longer manufactured).

Otherwise, you can order a new ring on eBay....

https://www.ebay.com/itm/Laserdisc-Play ... SwN0hcvRcB

You would have to remove the old ring and any residue left over. You can also try the plastidip but I have no experience with it but I do hear people swear by it.


d770 wrote:
Tried selecting B side of disc...noise at rear did not work ?? another jam somewhere perhaps !


You probably need a new loading belt. Side B jam ups are common w/ worn belts since they also shift the carriage during the turn around. Here is one that is available on eBay but I think you can find them cheaper elsewhere...

https://www.ebay.com/itm/PIONEER-CD-LAS ... SwzrxUvJm7


Last edited by ldfan on 21 Aug 2019, 16:19, edited 2 times in total.
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 21 Aug 2019, 14:50 
Jedi Master
Jedi Master
User avatar

Joined: 03 May 2004, 19:05
Posts: 8093
Location: Dullaware
Has thanked: 1218 times
Been thanked: 841 times
I would brush, I've never used the stuff.
There is someone on ebay selling new cut rings but I've never tried them.
Remove clean and then try your new option.
Good luck.
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 22 Aug 2019, 01:21 
Hardcore fan
Hardcore fan
User avatar

Joined: 10 May 2007, 03:12
Posts: 1516
Location: United States
Has thanked: 0 time
Been thanked: 337 times
Definitely the grip ring is bad. It does not spin up fast enough to properly read the TOC (Table Of Contents) so it defaults to a single sided disc mode and will not let you switch to side B (It won’t work anyway because of the gross grip ring slippage you have). When this bad they pretty much need to be replaced of cleaned and then coated with something like Plastic-Dip as the original ring is too far gone to recover back to near original gripping condition.
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 22 Aug 2019, 13:37 
Serious fan
Serious fan
User avatar

Joined: 19 Aug 2019, 07:23
Posts: 175
Location: Australia
Has thanked: 121 times
Been thanked: 42 times
Thankyou all members who have replied.. every post has helped me further along with the resurrection of this player.

Clearly my next step is to fix the slippage and then see how she goes from there.

Quickest way to do that is to go and grab a can of Plastidip tommorow !

On a side note...I bagged 50 LD's for 50$ today..mostly old titles but some worthy Criterion and Oscar winning... feels like it was a bargain deal.
now have some discs so need to get the player spinning nicely.
_________________
CLD-D770 OK
CLD-2850 FLD,R201
CLD-D780 MHolder, PSU C12
CLD-2290 Digital Prob
CLD-2590K Lots issues
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 22 Aug 2019, 13:46 
Absolute fan
Absolute fan
User avatar

Joined: 01 Feb 2018, 02:41
Posts: 1990
Location: Finland
Has thanked: 182 times
Been thanked: 382 times
d770 wrote:
On a side note...I bagged 50 LD's for 50$ today..mostly old titles but some worthy Criterion and Oscar winning... feels like it was a bargain deal.

Well that's a better deal than the "lots" I see for sale around here (Finland, not this board).
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 22 Aug 2019, 19:13 
Advanced fan
Advanced fan
User avatar

Joined: 02 Aug 2019, 02:29
Posts: 660
Location: Australia
Has thanked: 52 times
Been thanked: 85 times
d770 wrote:
Thankyou all members who have replied.. every post has helped me further along with the resurrection of this player.

Clearly my next step is to fix the slippage and then see how she goes from there.

Quickest way to do that is to go and grab a can of Plastidip tommorow !

On a side note...I bagged 50 LD's for 50$ today..mostly old titles but some worthy Criterion and Oscar winning... feels like it was a bargain deal.
now have some discs so need to get the player spinning nicely.


If you're talking our money then yeah that's a good deal, there's nothing that cheap close to me.
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 28 Aug 2019, 05:30 
Serious fan
Serious fan
User avatar

Joined: 19 Aug 2019, 07:23
Posts: 175
Location: Australia
Has thanked: 121 times
Been thanked: 42 times
Life has got me busy atm and so any further repair to the LD repair is on ice..however on my travels I snagged another box of LD's ..this time 50 for $70 AUD ...another rather older set but many top rated movies. Here is one old gem ..just the title alone does it for me!

As soon as Ive installed all these new blinds in the house in time for our summer I will be back at the player...got my can of Plastidip ready to go...and now plenty of discs waiting to enjoy.


Attachments:
body.jpg
body.jpg [ 148.09 KiB | Viewed 3982 times ]
_________________
CLD-D770 OK
CLD-2850 FLD,R201
CLD-D780 MHolder, PSU C12
CLD-2290 Digital Prob
CLD-2590K Lots issues
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 28 Aug 2019, 17:24 
Honest fan
Honest fan
User avatar

Joined: 15 Aug 2018, 02:00
Posts: 100
Location: United States
Has thanked: 2 times
Been thanked: 13 times
Yes, I have a 99 that needs that motor! Dibs!
(let me know when it's ready to ship. ;) )

Wish you were more local, I have several good players Id just swap you for that.
(offer open to any US side folks with a spare CLD-99 spindle motor)
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 29 Aug 2019, 09:55 
Serious fan
Serious fan
User avatar

Joined: 19 Aug 2019, 07:23
Posts: 175
Location: Australia
Has thanked: 121 times
Been thanked: 42 times
remav wrote:
Yes, I have a 99 that needs that motor! Dibs!
(let me know when it's ready to ship. ;) )

Wish you were more local, I have several good players Id just swap you for that.
(offer open to any US side folks with a spare CLD-99 spindle motor)


Will let you know ..at the moment still hoping it can fully fly again !
Im starting to realise how rare LD players are becoming.
_________________
CLD-D770 OK
CLD-2850 FLD,R201
CLD-D780 MHolder, PSU C12
CLD-2290 Digital Prob
CLD-2590K Lots issues
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 10 Sep 2019, 07:18 
Honest fan
Honest fan
User avatar

Joined: 15 Aug 2018, 02:00
Posts: 100
Location: United States
Has thanked: 2 times
Been thanked: 13 times
d770 wrote:
remav wrote:
Yes, I have a 99 that needs that motor! Dibs!
(let me know when it's ready to ship. ;) )

Wish you were more local, I have several good players Id just swap you for that.
(offer open to any US side folks with a spare CLD-99 spindle motor)


Will let you know ..at the moment still hoping it can fully fly again !
Im starting to realise how rare LD players are becoming.


I found a donor box & that should be "in the mail" now! Yippee! ...now Anyone want to venture a guess how much a spindle motor swap will be?
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 25 Jun 2021, 06:56 
Serious fan
Serious fan
User avatar

Joined: 19 Aug 2019, 07:23
Posts: 175
Location: Australia
Has thanked: 121 times
Been thanked: 42 times
Hello Everyone

Been a long time getting round to this Player again - but at last!

Bought a new Grip Ring and fitted - all ok there - Picture Quality very good happy with it...no more disc slippage!

Only issue remaining is now cannot yet play Side B - When you press the Side B button with a disc in the tray and the tray ejected ...you soon hear a clattering sound for a few seconds and then the player stops.

Made a couple of videos - it seems to be related to the Laser Carriage.

First Video shows the noise and the gears slipping on the Laser assembly/carriage

Second Video shows the 'play' in the Laser assembly/carriage at that position.

Anyone any ideas on whats going on here - something out of alignment with the track..something missing? or something else ? Thanks in advance



_________________
CLD-D770 OK
CLD-2850 FLD,R201
CLD-D780 MHolder, PSU C12
CLD-2290 Digital Prob
CLD-2590K Lots issues
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 25 Jun 2021, 09:12 
Serious fan
Serious fan
User avatar

Joined: 19 Aug 2019, 07:23
Posts: 175
Location: Australia
Has thanked: 121 times
Been thanked: 42 times
...note I can give the laser assembly a 'nudge' when it gets stuck and it will go on to the end of the track and rotate to side B as it should....I can then also Press Side A button and it will go back to Side A from Side B without issue or assistance and also play Side A again without issue.

One other thing to note ..Laser struggles to get a lock on Side B Disc...Plays Side A perfectly.
_________________
CLD-D770 OK
CLD-2850 FLD,R201
CLD-D780 MHolder, PSU C12
CLD-2290 Digital Prob
CLD-2590K Lots issues
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 26 Jun 2021, 06:13 
Hardcore fan
Hardcore fan
User avatar

Joined: 10 May 2007, 03:12
Posts: 1516
Location: United States
Has thanked: 0 time
Been thanked: 337 times
Might be able to re-grease the rail to get it to work. Also check to make sure the pin on the turn mechanism is lined up OK.
Offline
 Profile  
 
 Post subject: Re: Questions about - Pioneer CLD D770 (same as 703)
PostPosted: 27 Jun 2021, 13:59 
Serious fan
Serious fan
User avatar

Joined: 19 Aug 2019, 07:23
Posts: 175
Location: Australia
Has thanked: 121 times
Been thanked: 42 times
Thanks for replying...gave it some lubrication..Im sure that helped cheers.

Also want to share what I've found which has been part of the problem.....

I'd noticed there was so much play in the metal frame that contained the laser assembly...on further inspection the
'rear rubber support' underneath the Laser carriage metal assembly had moved and was barely supporting (not sure if carriage is the right name) see picture..

I think the unit had been stored vertically and with heat the glue had softened overtime and had slipped a bit... I have repositioned and reglued...the unit plays Side B everytime and the Laser now still clatters a little but always makes the turn.


Attachments:
rubber support2.jpg
rubber support2.jpg [ 313.64 KiB | Viewed 2590 times ]
_________________
CLD-D770 OK
CLD-2850 FLD,R201
CLD-D780 MHolder, PSU C12
CLD-2290 Digital Prob
CLD-2590K Lots issues
Offline
 Profile  
 
Display posts from previous:  Sort by  
 Page 2 of 3 [ 45 posts ]  Go to page Previous  1, 2, 3  Next


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: